Floor Scrubber Brushes, Pads and Squeegee Blades | Accelift
Distribution opportunities open in selected markets Become an Accelift distributor →

Scrubber Brushes, Pads and Squeegee Blades: Choosing and Replacing Them

Maintenance guide

A floor scrubber touches the floor in two places: the brush or pad at the front, which loosens the dirt, and the squeegee at the back, which collects the water. Both wear, and both decide how the floor looks afterwards. This guide explains which to fit and when to change them.

Brush or pad?

A brush has bristles that reach into joints and textured surfaces. A pad is a flat disc of abrasive fibre, held on a pad driver, that works on smooth floors only.

  • Brushes for concrete, tile with grout lines, anti-slip and textured floors. They last longer and cope with small debris.
  • Pads for smooth, glossy floors such as vinyl, polished stone and coated floors, where an even finish matters. They are cheap, but they wear quickly and tear on rough surfaces.
Table of scrubber brushes and pads: soft, hard and abrasive brushes, red, green, blue and black pads, and where to use each
Brushes and pads from gentle to aggressive.

Pad colours follow a convention used by most makers: the lighter the colour, the gentler the pad. White polishes, red cleans daily, green and blue scrub deeply, and black strips old polish. A pad that is too aggressive dulls a glossy floor in one pass, so test on a corner first.

One brush or two

A single disc brush is enough for light daily soil. Two brushes turning against each other scrub harder in the same pass and keep the machine running straight. That is why our JC75/85-B and JC150 have two.

AcceClean JC75/85-B ride-on floor scrubber with two brushes and a rear squeegee
A twin-brush ride-on: two discs at the front, the squeegee behind the rear wheels.

When to replace a brush

  • The bristles are worn down to about 15 mm, or the wear indicator bristles are level with the rest.
  • The bristles are bent flat and no longer stand up after drying.
  • The brush wears on one side. Check that the brush deck is level before fitting a new one.

Take the brush off after each shift, rinse it and hang it up. A brush left under the weight of the machine goes flat on one side. In daily use a disc brush typically lasts several months; a pad lasts days or weeks.

Squeegee blades

The squeegee has two blades. The front blade has slots that let the water through; the rear blade seals against the floor so that the suction can lift the water. The rear blade does the work and wears first.

  • Natural rubber. Soft, dries smooth floors well and costs little. It does not last on oily floors.
  • Polyurethane. Resists oil, grease and chemicals. The choice for factories and workshops.
  • Red abrasion-resistant rubber. The longest life on rough concrete, at a higher price.

Four edges, not one

A squeegee blade has four working edges. When the edge on the floor is rounded or nicked, take the blade off and turn it, end for end and then top to bottom, to bring a fresh edge down. Replace the blade only when all four edges are used. Many blades are thrown away after a quarter of their life.

Signs that a blade needs turning or replacing:

  • Streaks or a thin line of water behind the machine
  • A rounded edge that you can feel with a finger
  • Cuts or nicks, often from metal chips or pallet nails
  • A blade that has gone hard or wavy

Sweepers

On a sweeper the wear parts are the main brush, the side brushes and the filter. Side brushes wear fastest, because they run along kerbs and walls. Lower the main brush as it wears, so that it keeps a sweeping strip of a few centimetres on the floor, and replace it when the adjustment runs out.

If the machine still leaves water behind with a good blade, the cause is elsewhere: see floor scrubber troubleshooting. Dealers can order brushes, pads and blades for AcceClean scrubbers with any shipment; contact us with the model.

Mixed containers welcome

Planning a container for your market?

Send us the models you need. We will work out the mix, the loading plan and the price.